How to Repair Scratches and Dents in Wood Baby Crib

Download Article

Download Article

If you've noticed an unsightly paring in your wood floor or article of furniture, you might fright that it's ruined for adept. Simply there'due south really a very elementary solution for lifting dents from soft wood surfaces—the magic combination of heat and wet. By running an ordinary clothes fe over the spot, you can erase shallow dents and dings and restore the woods to its original smoothness. This ready takes merely a few minutes, and when you're finished you lot'll barely be able to tell that at that place was ever a flaw in the start identify.

1. i

   Dab the dent with water. Cascade about an ounce of water over the affected area, just plenty to cover the paring and a small-scale role of the surrounding woods. Make sure the dent is completely wet. Pooling inside the depression itself is a expert sign that the spot has been thoroughly soaked.^[1]

   • Using an eyedropper or kitchen baster will give y'all more than control over where you lot apply the water.
   • If there's whatsoever serious breakage or chipping around the dent, you may demand to have the surface repaired professionally to avoid making it worse.

2. 2

   Place a damp paper towel or piece of cloth over the dent. Moisture the cloth or paper towel and wring out the excess water, then lay information technology directly on top of the paring. This will provide a footling added moisture while likewise creating a buffer that will help protect the wood from being damaged by the heat of the iron.^[two]

   • It may be a good thought to use an old t-shirt, dusting rag or some other piece of fabric that yous don't care about potentially ruining.
   • If the dent is located on the side or corner of a article of furniture, you might need to hold the cloth in place with your gratuitous hand while you steam the wood.^[3]

   Advertizing

3. three

   Give the water time to soak into the wood. Permit the forest sit for a minute or two to absorb as much moisture as possible. As the water seeps into the forest, information technology will crusade it to soften and become pliable. One time you utilise rut to the spot, the wood will aggrandize and the dent volition lift right out.

   • The deeper the water penetrates into the wood, the more constructive the steaming process will be.

   Advertisement

1. one

   Heat up a clothes iron. Plug the iron in and turn it on to the highest setting. Requite it a few minutes to first warming upwardly—it needs to be overnice and hot in gild to work effectively.^[4]

   • The iron will be very hot after you lot've turned it on. Touching the surface could issue in a painful fire.
   • When you're non using the iron, set it on a hard, level surface where it won't get tipped over.

2. 2

   Run the atomic number 26 over the dented area. Press the iron into the cloth above the paring and motility it around using deadening circular motions. Make a few passes, gradually widening the area that you're ironing. Keep heating the wood until the cloth is dry out, then lift a corner to bank check your progress.^[5]

   • The heat from the iron (coupled with the moisture of the water) will cause the compressed wood in the paring to swell, returning it to its original grade.
   • Endeavor non to let the fe sit in ane place for too long, or information technology may scorch the textile or the wood underneath.^[6]

3. iii

   Rewet the wood and echo equally needed. A single ironing might exist all you need to bargain with minor dents. For more astringent depressions or areas with multiple marks, go along calculation h2o and ironing slowly until the worst of the dents accept been raised.^[7]

   • Betwixt attempts, be sure to dampen the textile with fresh water or grab a fresh newspaper towel.
   • You might non be able to remove deep dents entirely. However, steaming volition help to level them out and make them less noticeable.^[8]

   Advertisement

1. i

   Let the wood dry completely. Wet wood is soft, which makes it prone to splitting and breakage. Let the surface to air dry earlier handling it. In the meantime, hold off on replacing furniture or setting other objects on it to avoid farther accidents.^[ix]

   • The heat of the iron volition have evaporated most of the moisture, simply it may take a few hours to regain its total hardness and rigidity.
   • The woods will shrink somewhat as it dries, which can cause problems if you begin sanding or putting force per unit area on it as well soon.

2. 2

   Smooth out the wood with sandpaper. In some cases, small-scale flaws may be left backside in the wood, or the water might produce a slight discoloration. You lot tin remedy this by running a square of high-dust sandpaper over the area until it blends in with the forest around information technology.^[x]

   • Use light, polish strokes to avoid scratching the wood surface, which may have been weakened past the dent.

3. iii

   Brush on a protective finish. When you're done buffing imperfections out of finished surfaces, be sure to bear on them up with a fresh coat of paint or laminate. This will assistance conceal whatever remaining traces of the dent and act every bit a barrier confronting knocks and bumps in the time to come.^[11]

   • In most cases, a single glaze volition practice to cover up the spot where the paring was.
   • Let the refinished surface to air dry out overnight before touching it.

4. 4

   Repair big dents with a filler textile. Steaming won't ever be plenty to eliminate dents. Deep gouges and spots with breaking, splitting or chipping should be looked at by a professional. Extensive damage can usually be repaired with a durable epoxy or lacquer filler.^[12]

   • For bigger jobs, have a woodworker cutting a special woods inlay to fit the damaged area.^[13]
   • Afterwards, the repaired surface will likely demand to be resealed or stained.

   Advertisement

Add together New Question

• Question

  I dropped my laptop on my hardwood floors, which left dents and scratches. Since it was a MacBook, some of the wood is the tiniest flake splintered. Volition using an iron mayhap damage the flooring?

  

  Jack Pierce_26

  Customs Reply

  Yes, irons can possibly create fire hazards. Instead, employ a file, axe, or annihilation else that will remove chips. Although a file is less efficient, information technology is less unsafe. You can replace it with a new plank, foursquare, or any your floor'south wood is made out of, and the shape.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

• Using your iron's steam feature may make information technology fifty-fifty more than useful for lifting out dents.

• Heat will work all-time for removing minor dents from softer, unfinished varieties of wood, similar pine, birch or cedar.

• Consider covering vulnerable surfaces with cushions, throw rugs or place mats.

• Applying a coat of varnish or lacquer can safeguard your wood furniture or flooring from drops, spills and other accidents.

Thanks for submitting a tip for review!

Advertisement

• Don't let the iron to come into straight contact with the wood surface.

• Avert using a synthetic fabric to embrace the wood. These tin easily cook under the heat of the iron.

• In that location's no guarantee that steaming volition work on hardwood surfaces, or those layered thickly with paint or clear glaze.

Advert

Things You lot'll Need

• Clothes iron
• Water
• Sparse cloth or paper towel
• High-grit sandpaper
• Eyedropper or baster (optional)
• Lacquer, varnish or acrylic paint (optional)

About This Article

Commodity Summary X

To remove a dent from forest, start by pouring about an ounce of water onto it. Then, place a damp cloth over the dent. Let the h2o soak in while you heat upward a clothes fe to the highest setting. When your fe has heated upward, press information technology to the fabric and move it in dull circles. Once the cloth is dry, check the dent to see if it's risen. If the paring is still bad, moisture the fabric again and repeat the process. After the wood's dried for a few hours, brush on a protective finish, like paint or laminate, to assist protect the woods and cover up the dent. For more than tips, including how to repair large dents with filler, read on!

Did this summary aid you?

Cheers to all authors for creating a page that has been read 124,373 times.

Did this article help y'all?

rodgersredet1948.blogspot.com

Source: https://www.wikihow.com/Remove-a-Dent-from-Wood

Share this post